Partial
Eryone ASA-GF on the Kobra 3 Max V2
Nozzle, Bed, Speed, Drying. Source: Eryone product page · Last checked 19 October 2026
Source: Anycubic product page · Last checked 19 October 2026
How we verify: a figure is copied from a named source, and a missing figure stays blank. Methodology.
FilamentFacts may earn a commission when you buy through links on this page. As an Amazon Associate we earn from qualifying purchases.
- Nozzle260–280 °C(500–536 °F)
- Bed90–100 °C(194–212 °F)
- Speed30–150 mm/s
- Dry80 °C(176 °F)for 4 h
- Density1.17 g/cm³
Nozzle, Bed, Speed, Drying. Source: Eryone product page · Last checked 19 October 2026
Compatibility
- The listed nozzle maximum of 280 °C (536 °F) is within this printer's maximum of 300 °C (572 °F).
- The listed bed range reaches 100 °C (212 °F), above this printer's maximum of 90 °C (194 °F). This printer cannot reach the full recommended range. The low end, 90 °C (194 °F), is within that maximum.
- Whether an enclosure is required is not in our current sources.
- This filament is recorded as needing a hardened nozzle. The stock nozzle is hardened.
Related answers
- Which nozzle (brass, hardened, 0.6mm) should I use for which filament?
- What is the best filament for outdoor use?
- What filament should I use for heat?
- Are ABS/ASA fumes dangerous, and do I need ventilation?
Kobra 3 Max V2 maximums: nozzle 300 °C (572 °F), bed 90 °C (194 °F).
Filament page · Kobra 3 Max V2
Sources & notes
Anycubic Kobra 3 Max V2 with Eryone ASA-GF: The listed bed range reaches 100 °C (212 °F), above this printer's maximum of 90 °C (194 °F). This printer cannot reach the full recommended range. The low end, 90 °C (194 °F), is within that maximum.
Dataset imported 13 October 2026. Manufacturer page checked 19 October 2026.
Eryone product page · checked 19 October 2026 · Printer source · Filament JSON
The specification table lists a hardened steel nozzle at a maximum of 300 °C, standard diameter 0.4 mm, and a hotbed maximum of 90 °C.
Extruder type is short distance extrusion with a dual-gear extruder. Recommended speed is 300 mm/s and the maximum is 600 mm/s.
ACE 2 Pro is listed as standard 4 colors, up to 8 colors, with drying up to 65 °C. Supporting filaments are PLA, PETG, and TPU, and the table says TPU 95A is not compatible with the ACE 2 Pro.
The product FAQ says the Combo prints PLA, PETG, and TPU (68D), and that printing with PA and PC is not recommended. The page does not state an enclosure.
Questions
Can the Anycubic Kobra 3 Max V2 reach the listed ASA-GF nozzle temperature?
The listed nozzle maximum of 280 °C (536 °F) is within this printer's maximum of 300 °C (572 °F).
Can the Kobra 3 Max V2 reach the listed bed temperature?
The listed bed range reaches 100 °C (212 °F), above this printer's maximum of 90 °C (194 °F). This printer cannot reach the full recommended range. The low end, 90 °C (194 °F), is within that maximum.
Is an enclosure required?
Whether an enclosure is required is not in our current sources.
Is a hardened nozzle recorded?
This filament is recorded as needing a hardened nozzle. The stock nozzle is hardened.