{
  "opening": "These ranked rows list 190–260 °C (374–500 °F).",
  "question": "How do I find the right nozzle temperature for a filament (temp tower)?",
  "slug": "temp_general",
  "useCase": "troubleshooting",
  "useCaseLabel": "Troubleshooting",
  "updated": "2026-10-17",
  "shortAnswer": "Start inside the nozzle range stored for the spool you loaded, then print a temperature tower after cooling, retraction, and the first layer are already behaving. A tower that strings at every step is a moisture or retraction problem, and a tiny part that twists is a cooling problem.",
  "recommendedMaterials": [
    "pla",
    "petg",
    "abs"
  ],
  "printerConsiderations": [
    "On r/3Dprinting spzme6 the poster had already lowered nozzle temperature on a 0.100 inch cylinder and it still twisted. The top comment is the four words Minimum time per layer. The next comments say print several at once so each layer can cool, slow down, and check for a silicone sock on the heater block.",
    "On r/FixMyPrint w6u60d the poster was at 185 degrees on an Ender 3 V2, 0.12 mm layers, 8 mm retraction at 50 mm/s, and the comments name power-loss recovery pauses and the Z seam, not a new setpoint.",
    "Match the tower's top and bottom to the row you loaded. PolyLite PLA stops at 230 °C (446 °F). PolyLite PETG starts at 220 °C (428 °F). eSUN ABS+ starts at 230 °C (446 °F)."
  ],
  "pros": [
    "The three rows are three different nozzle windows, so a single tower recipe is not copied onto PLA, PETG, and ABS.",
    "The stringing tower and the twisting cylinder are kept as separate failures."
  ],
  "cons": [
    "A comment on r/3Dprinting spzme6 mentions a temperature tower only after esteps. These threads never show a finished tower with a chosen step.",
    "The titles that say 200 and 60, or 185 degrees, do not name Celsius. Those figures stay the posters' words."
  ],
  "community": "r/3Dprinting spzme6 is a tiny cylinder that still twisted after the poster lowered nozzle temperature. The leading comment is Minimum time per layer, and a score-27 comment says the layer underneath is still hot, asks for more cooling and a slower print, and asks whether a silicone sock is on the heater block. r/FixMyPrint vmmrlq is a bad print at 200 nozzle and 60 bed. The leading comment lists a clog, moisture, and not enough extrusion, and says to re-tune if something changed. A later comment asks whether popping sounds are moisture. r/3Dprinting s3e3gn already tried dish soap, 97% IPA, a little glue, and higher nozzle temperatures on Prusa pearl blue. The comments point at Live-Z being too high, a 7x7 bed mesh, and the first-layer squish. r/3Dprinting saw4s2 asks why a whole temperature tower is stringing. The comments say retraction, Bowden fittings, the nozzle, and low-quality filament, and two comments say the filament is wet, including filament that is new to the printer. r/FixMyPrint w6u60d is blobs at 185 degrees on an Ender 3 V2. The leading comment says turn off power-loss protection.",
  "related": [
    "stringing",
    "pla_print",
    "drying",
    "petg_print",
    "abs_print"
  ],
  "faq": [
    {
      "q": "Should I change nozzle temperature before the first layer sticks?",
      "a": "No. On r/3Dprinting s3e3gn the poster had already raised nozzle temperature, and the comments still send the printer back to Live-Z and the first layer. The PLA print guide is that sequence."
    },
    {
      "q": "What does a temperature tower that strings at every step mean?",
      "a": "On r/3Dprinting saw4s2 the comments split the cause across retraction, the Bowden path, the nozzle, filament quality, and water. Wet filament is also the popping question on r/FixMyPrint vmmrlq. Use the stringing guide and the drying guide before picking a new setpoint."
    }
  ],
  "sources": [
    {
      "title": "PolyLite PLA technical data sheet",
      "url": "https://cdn.shopify.com/s/files/1/0548/7299/7945/files/PolyLite_PLA_TDS_EN_V5.4.pdf",
      "kind": "datasheet"
    },
    {
      "title": "PolyLite PETG technical data sheet",
      "url": "https://cdn.shopify.com/s/files/1/0548/7299/7945/files/PolyLite_PETG_TDS_EN_V5.4.pdf",
      "kind": "datasheet"
    },
    {
      "title": "Polymaker US PolyLite PLA product page",
      "url": "https://us.polymaker.com/products/polylite-pla",
      "kind": "manufacturer"
    },
    {
      "title": "Open Filament Database, eSUN 3D ABS+",
      "url": "https://api.openfilamentdatabase.org/api/v1/brands/esun_3d/materials/ABS/filaments/abs+/index.json",
      "kind": "other"
    },
    {
      "title": "Community source, r/3Dprinting spzme6",
      "url": "https://www.reddit.com/r/3Dprinting/comments/spzme6/",
      "kind": "reddit"
    },
    {
      "title": "Community source, r/FixMyPrint vmmrlq",
      "url": "https://www.reddit.com/r/FixMyPrint/comments/vmmrlq/",
      "kind": "reddit"
    },
    {
      "title": "Community source, r/3Dprinting s3e3gn",
      "url": "https://www.reddit.com/r/3Dprinting/comments/s3e3gn/",
      "kind": "reddit"
    },
    {
      "title": "Community source, r/3Dprinting saw4s2",
      "url": "https://www.reddit.com/r/3Dprinting/comments/saw4s2/",
      "kind": "reddit"
    },
    {
      "title": "Community source, r/FixMyPrint w6u60d",
      "url": "https://www.reddit.com/r/FixMyPrint/comments/w6u60d/",
      "kind": "reddit"
    }
  ],
  "recommendations": [
    {
      "rank": 1,
      "note": "PolyLite PLA lists a nozzle of 190–230 °C (374–446 °F) and a bed of 25–60 °C (77–140 °F) on the US product page checked for this catalog, with drying at 55 °C (131 °F) for 6 h. A temperature tower for this spool stays inside 190–230 °C (374–446 °F).",
      "brand": "Polymaker",
      "product": "Polylite PLA",
      "material": "PLA",
      "url": "/brand/polymaker/polylite-pla",
      "nozzle": "190–230 °C (374–446 °F)",
      "bed": "25–60 °C (77–140 °F)",
      "pricePerKg": null,
      "datasheetUrl": "https://cdn.shopify.com/s/files/1/0548/7299/7945/files/PolyLite_PLA_TDS_EN_V5.4.pdf",
      "affiliateUrl": null
    },
    {
      "rank": 2,
      "note": "PolyLite PETG lists a nozzle of 220–250 °C (428–482 °F) and a bed of 70–90 °C (158–194 °F) in the Open Filament Database, and the PolyLite PETG technical data sheet is the datasheet link. That is a different window from the PLA row.",
      "brand": "Polymaker",
      "product": "Polylite PETG",
      "material": "PETG",
      "url": "/brand/polymaker/polylite-petg",
      "nozzle": "220–250 °C (428–482 °F)",
      "bed": "70–90 °C (158–194 °F)",
      "pricePerKg": null,
      "datasheetUrl": "https://cdn.shopify.com/s/files/1/0548/7299/7945/files/PolyLite_PETG_TDS_EN_V5.4.pdf",
      "affiliateUrl": null
    },
    {
      "rank": 3,
      "note": "eSUN ABS+ lists a nozzle of 230–260 °C (446–500 °F) and a bed of 90–110 °C (194–230 °F) in the Open Filament Database. Drying and enclosure required are blank on the row.",
      "brand": "eSUN 3D",
      "product": "ABS+",
      "material": "ABS",
      "url": "/brand/esun-3d/abs-plus",
      "nozzle": "230–260 °C (446–500 °F)",
      "bed": "90–110 °C (194–230 °F)",
      "pricePerKg": null,
      "datasheetUrl": null,
      "affiliateUrl": null
    }
  ]
}