{
  "question": "Where do I get good slicer profiles for a filament?",
  "slug": "profiles",
  "useCase": "troubleshooting",
  "useCaseLabel": "Troubleshooting",
  "updated": "2026-10-16",
  "shortAnswer": "Start from the slicer profile or the manufacturer sheet for that spool, then calibrate temperature, flow, and pressure advance on the spool you loaded.",
  "recommendedMaterials": [
    "pla",
    "petg"
  ],
  "printerConsiderations": [
    "A built-in generic PLA profile is a start only when it matches the spool. The three PLA beds above are 35–45 °C (95–113 °F), 25–60 °C (77–140 °F), and 40–60 °C (104–140 °F).",
    "Calibrate flow and pressure advance after the temperature is in range. The flow guide is that step. This page does not publish a flow percent.",
    "Retraction in a default profile is not a filament identity. One bank variant names a Cura retraction of 0.8 mm at 45 mm/s on an Ender. That is a user setting, not a catalog cell."
  ],
  "pros": [
    "Each temperature belongs to a named sheet or Open Filament Database row.",
    "The first step is a profile you can point at, then a calibration on that spool."
  ],
  "cons": [
    "The editorial summary names OrcaSlicer calibration tools. The top comments supplied for these five threads do not mention OrcaSlicer, so this page does not treat that name as something these threads said.",
    "Two of the supplied comments are jokes about a spider print. They are not a profile."
  ],
  "community": "The editorial summary says to start from the slicer's built-in or manufacturer profile, then calibrate temperature, flow, and pressure advance per spool, and it names OrcaSlicer. The supplied top comments do not say OrcaSlicer. One comment on r/FixMyPrint vq9gnz guesses that inner-before-outer walls is not enabled in Cura, and the same thread is about droopy overhangs. The r/3Dprinting 105sfr7 comments supplied here are jokes. This page keeps the manufacturer-sheet start, which the catalog can show, and leaves OrcaSlicer as an unverified line in the summary.",
  "related": [
    "flow",
    "filament_quality",
    "pla_print",
    "drying",
    "petg_print"
  ],
  "faq": [
    {
      "q": "Do the supplied comments recommend OrcaSlicer?",
      "a": "No. The editorial summary names OrcaSlicer. The top comments in this bank for these five threads do not. One of them is about inner-before-outer walls in Cura. Two are jokes. Start from the manufacturer row, then use the flow guide."
    },
    {
      "q": "Can one PLA profile cover Bambu, Polymaker, and Prusament?",
      "a": "No. Bambu PLA Basic lists a bed of 35–45 °C (95–113 °F). PolyLite PLA lists 25–60 °C (77–140 °F). Prusament PLA lists 40–60 °C (104–140 °F). Load the row for the spool."
    }
  ],
  "sources": [
    {
      "title": "Bambu PLA Basic technical data sheet V3.0",
      "url": "https://cdn.shopify.com/s/files/1/0584/7236/6216/files/Bambu_PLA_Basic_Technical_Data_Sheet_bf3411ce-be39-4db7-9669-1b4671d2196b.pdf?v=1734060943",
      "kind": "datasheet"
    },
    {
      "title": "PolyLite PLA technical data sheet",
      "url": "https://cdn.shopify.com/s/files/1/0548/7299/7945/files/PolyLite_PLA_TDS_EN_V5.4.pdf",
      "kind": "datasheet"
    },
    {
      "title": "Polymaker US PolyLite PLA product page",
      "url": "https://us.polymaker.com/products/polylite-pla",
      "kind": "manufacturer"
    },
    {
      "title": "Open Filament Database, Prusament PLA",
      "url": "https://api.openfilamentdatabase.org/api/v1/brands/prusament/materials/PLA/filaments/pla/index.json",
      "kind": "other"
    },
    {
      "title": "Bambu Lab PETG HF technical data sheet",
      "url": "https://store.bblcdn.com/ce12d65176a94f1086e6aefa238e62e2.pdf",
      "kind": "datasheet"
    },
    {
      "title": "Community source, r/3Dprinting 105sfr7",
      "url": "https://www.reddit.com/r/3Dprinting/comments/105sfr7/",
      "kind": "reddit"
    },
    {
      "title": "Community source, r/FixMyPrint vq9gnz",
      "url": "https://www.reddit.com/r/FixMyPrint/comments/vq9gnz/",
      "kind": "reddit"
    },
    {
      "title": "Community source, r/BambuLab 14uype2",
      "url": "https://www.reddit.com/r/BambuLab/comments/14uype2/",
      "kind": "reddit"
    },
    {
      "title": "Community source, r/BambuLab 1tr09f9",
      "url": "https://www.reddit.com/r/BambuLab/comments/1tr09f9/",
      "kind": "reddit"
    },
    {
      "title": "Community source, r/3Dprinting sedzai",
      "url": "https://www.reddit.com/r/3Dprinting/comments/sedzai/",
      "kind": "reddit"
    }
  ],
  "recommendations": [
    {
      "rank": 1,
      "note": "A manufacturer starting point, not a universal PLA profile. PLA Basic lists a nozzle of 190–230 °C (374–446 °F), a bed of 35–45 °C (95–113 °F), and drying at 50 °C (122 °F) for 8 h on the Bambu PLA Basic technical data sheet V3.0.",
      "brand": "Bambu Lab",
      "product": "PLA Basic",
      "material": "PLA",
      "url": "/brand/bambu-lab/pla-basic",
      "nozzle": "190–230 °C (374–446 °F)",
      "bed": "35–45 °C (95–113 °F)",
      "pricePerKg": null,
      "datasheetUrl": "https://cdn.shopify.com/s/files/1/0584/7236/6216/files/Bambu_PLA_Basic_Technical_Data_Sheet_bf3411ce-be39-4db7-9669-1b4671d2196b.pdf?v=1734060943",
      "affiliateUrl": null
    },
    {
      "rank": 2,
      "note": "PolyLite PLA lists a nozzle of 190–230 °C (374–446 °F), a bed of 25–60 °C (77–140 °F), a print speed of 40–60 mm/s, and drying at 55 °C (131 °F) for 6 h. The bed range is this sheet, which is wider than the Bambu PLA Basic bed.",
      "brand": "Polymaker",
      "product": "Polylite PLA",
      "material": "PLA",
      "url": "/brand/polymaker/polylite-pla",
      "nozzle": "190–230 °C (374–446 °F)",
      "bed": "25–60 °C (77–140 °F)",
      "pricePerKg": null,
      "datasheetUrl": "https://cdn.shopify.com/s/files/1/0548/7299/7945/files/PolyLite_PLA_TDS_EN_V5.4.pdf",
      "affiliateUrl": null
    },
    {
      "rank": 3,
      "note": "Prusament PLA from the Open Filament Database. Nozzle 205–225 °C (401–437 °F) and bed 40–60 °C (104–140 °F). Drying is not stored. Use that row when the spool is Prusament, not the Bambu sheet.",
      "brand": "Prusament",
      "product": "PLA",
      "material": "PLA",
      "url": "/brand/prusament/pla",
      "nozzle": "205–225 °C (401–437 °F)",
      "bed": "40–60 °C (104–140 °F)",
      "pricePerKg": null,
      "datasheetUrl": null,
      "affiliateUrl": null
    },
    {
      "rank": 4,
      "note": "The same rule on a second material. PETG HF lists a nozzle of 230–260 °C (446–500 °F), a bed of 65–75 °C (149–167 °F), drying at 65 °C (149 °F) for 8 h, and print speed up to 300 mm/s. A PLA profile is the wrong start.",
      "brand": "Bambu Lab",
      "product": "PETG HF",
      "material": "PETG",
      "url": "/brand/bambu-lab/petg-hf",
      "nozzle": "230–260 °C (446–500 °F)",
      "bed": "65–75 °C (149–167 °F)",
      "pricePerKg": null,
      "datasheetUrl": "https://store.bblcdn.com/ce12d65176a94f1086e6aefa238e62e2.pdf",
      "affiliateUrl": null
    }
  ]
}