{
  "opening": "These PLA rows list 190–230 °C (374–446 °F).",
  "question": "How do I handle filament runout / switching rolls mid-print?",
  "slug": "filament_runout",
  "useCase": "troubleshooting",
  "useCaseLabel": "Troubleshooting",
  "updated": "2026-10-18",
  "shortAnswer": "On the Prusa XL thread, the printer kept going because the filament sensor was likely off. Recalibrate it, then preheat and push the new filament through the nozzle. The other four threads are a model, a stopped extruder, a snapped hotend, and an ABS bed.",
  "recommendedMaterials": [
    "pla"
  ],
  "printerConsiderations": [
    "The Prusa Knowledge Base page for the MK3 non-S filament sensor says a runout pauses the print, unloads the last centimeters, and asks for a new spool. If filament is stuck in the PTFE tube, the page says push it out with the new filament. That is the same move as the score-50 comment. The page is the MK3 non-S article. The thread is an XL.",
    "A score-7 comment on r/prusa3d 1hps0qb says the sensor stays off after the user dismisses an unloaded-filament error, until someone turns it back on. The XL page is the printer record.",
    "r/BambuLab 1i3f59y is a bend-mid-print model whose title says it reduces filament swaps. The score-18 comment asks to film a YouTube short. It does not describe a sensor."
  ],
  "pros": [
    "The XL comments agree on one check: the sensor is off, or it needs a calibration.",
    "The MK3 non-S article and the score-50 comment use the same recovery: push the new filament through."
  ],
  "cons": [
    "This set does not document an AMS refill, an M600 pause, or a splice. Those procedures are absent from the retrieved comments.",
    "Four of the five titles say mid-print and then describe a different failure."
  ],
  "community": "r/prusa3d 1hps0qb is a Prusa XL that kept moving after the filament ran out. The score-50 comment says the sensor is probably off, or it needs recalibration, and says to preheat and feed the new filament through the nozzle. A score-15 comment says the sensors are off. A score-10 comment has pushed filament through on an MK3 or MK4. A score-7 comment says dismissing an unloaded-filament error leaves the sensor off. r/BambuLab 1i3f59y is a bend-mid-print model. r/ender3 13j4ucp is Elegoo PLA that stops extruding. r/BambuLab 11g424j is a snapped hotend with PA12-CF still in the part. r/3Dprinting 1n76prc is Polymaker Polylite ABS letting go of a PEI bed.",
  "related": [
    "clog",
    "underext",
    "ams",
    "mk4_filament"
  ],
  "faq": [
    {
      "q": "What does the MK3 article say to do with filament stuck in the tube?",
      "a": "Push it out with the new filament. The article also says a working sensor pauses the print and unloads the last centimeters. The XL thread's score-50 comment uses the push-through step and first tells you to check that the sensor is on."
    },
    {
      "q": "Which filament did the XL run out of?",
      "a": "The thread does not name one. ELEGOO PLA is the filament named on the Ender 3 extrusion-stop thread, which the comments treat as heat creep, a tangle, or layer height."
    }
  ],
  "sources": [
    {
      "title": "Prusa Knowledge Base, filament sensor MK3 (non-S)",
      "url": "https://help.prusa3d.com/article/filament-sensor-mk3-non-s_2125",
      "kind": "manufacturer"
    },
    {
      "title": "Prusament PLA Jet Black",
      "url": "https://www.prusa3d.com/product/prusament-pla-jet-black-1kg/",
      "kind": "manufacturer"
    },
    {
      "title": "ELEGOO PLA 1.75 mm",
      "url": "https://us.elegoo.com/products/pla-filament-1-75mm-colored-1kg",
      "kind": "manufacturer"
    },
    {
      "title": "Bambu PLA Basic technical data sheet V3.0",
      "url": "https://cdn.shopify.com/s/files/1/0584/7236/6216/files/Bambu_PLA_Basic_Technical_Data_Sheet_bf3411ce-be39-4db7-9669-1b4671d2196b.pdf?v=1734060943",
      "kind": "datasheet"
    },
    {
      "title": "Community source, r/BambuLab 1i3f59y",
      "url": "https://www.reddit.com/r/BambuLab/comments/1i3f59y/",
      "kind": "reddit"
    },
    {
      "title": "Community source, r/ender3 13j4ucp",
      "url": "https://www.reddit.com/r/ender3/comments/13j4ucp/",
      "kind": "reddit"
    },
    {
      "title": "Community source, r/BambuLab 11g424j",
      "url": "https://www.reddit.com/r/BambuLab/comments/11g424j/",
      "kind": "reddit"
    },
    {
      "title": "Community source, r/3Dprinting 1n76prc",
      "url": "https://www.reddit.com/r/3Dprinting/comments/1n76prc/",
      "kind": "reddit"
    },
    {
      "title": "Community source, r/prusa3d 1hps0qb",
      "url": "https://www.reddit.com/r/prusa3d/comments/1hps0qb/",
      "kind": "reddit"
    }
  ],
  "recommendations": [
    {
      "rank": 1,
      "note": "ELEGOO PLA lists a nozzle of 190–230 °C (374–446 °F) and a bed of 35–65 °C (95–149 °F). r/ender3 13j4ucp names Elegoo PLA black. That print stopped extruding. The comments say heat creep, a tangle, or a 0.8 mm layer on a 0.4 mm nozzle. They do not describe a roll running out.",
      "brand": "ELEGOO",
      "product": "PLA",
      "material": "PLA",
      "url": "/brand/elegoo/pla",
      "nozzle": "190–230 °C (374–446 °F)",
      "bed": "35–65 °C (95–149 °F)",
      "pricePerKg": null,
      "datasheetUrl": null,
      "affiliateUrl": null
    },
    {
      "rank": 2,
      "note": "The Open Filament Database lists Prusament PLA at 205–225 °C (401–437 °F) and a bed of 40–60 °C (104–140 °F). The Jet Black product page lists a nozzle of 215 °C (419 °F) and a bed of 50–60 °C (122–140 °F). The XL runout thread does not name a polymer. Prusament PLA is the brand row for that printer family.",
      "brand": "Prusament",
      "product": "PLA",
      "material": "PLA",
      "url": "/brand/prusament/pla",
      "nozzle": "205–225 °C (401–437 °F)",
      "bed": "40–60 °C (104–140 °F)",
      "pricePerKg": null,
      "datasheetUrl": null,
      "affiliateUrl": null
    },
    {
      "rank": 3,
      "note": "Bambu PLA Basic lists 190–230 °C (374–446 °F) and a bed of 35–45 °C (95–113 °F) on technical data sheet V3.0. r/BambuLab 1i3f59y and 11g424j are Bambu posts. Neither is a roll running out. The first is a color-swap model. The second is a hotend that snapped.",
      "brand": "Bambu Lab",
      "product": "PLA Basic",
      "material": "PLA",
      "url": "/brand/bambu-lab/pla-basic",
      "nozzle": "190–230 °C (374–446 °F)",
      "bed": "35–45 °C (95–113 °F)",
      "pricePerKg": null,
      "datasheetUrl": "https://cdn.shopify.com/s/files/1/0584/7236/6216/files/Bambu_PLA_Basic_Technical_Data_Sheet_bf3411ce-be39-4db7-9669-1b4671d2196b.pdf?v=1734060943",
      "affiliateUrl": null
    }
  ]
}