{
  "opening": "A 50 °C (122 °F) dryer can dry 19 of 236 filaments in our data, mostly PLA. A filament counts when the maker's drying maximum is at or below that dryer.",
  "question": "Is a 50 °C (122 °F) filament dryer enough for PETG or nylon?",
  "slug": "dryer_50c",
  "useCase": "drying",
  "useCaseLabel": "Drying",
  "updated": "2026-10-25",
  "shortAnswer": "No. A 50 °C (122 °F) dryer is below every PETG row in the drying dataset, 55–70 °C (131–158 °F), and below every nylon row, 70–110 °C (158–230 °F). Of 60 PLA rows, 14 list a maximum of 50 °C (122 °F) or less, 9 list a range that starts at 50 °C (122 °F) and goes higher, and 37 list a minimum above 50 °C (122 °F).",
  "recommendedMaterials": [
    "pla",
    "petg",
    "pa6"
  ],
  "printerConsiderations": [
    "50 °C (122 °F) is the Bambu PLA Basic blast-oven line. It is not a PETG setpoint and it is not a nylon setpoint.",
    "The same Bambu PLA Basic sheet also lists an X1 heatbed cycle at 60–70 °C (140–158 °F) for 12 hours. That second line is a printer bed, not proof that 50 °C (122 °F) dries every PLA.",
    "PA-CF is a separate family in the dataset, 11 rows, and it also starts at 70 °C (158 °F). A 50 °C (122 °F) dryer is below those rows too."
  ],
  "pros": [
    "Every temperature on this page is a row in the drying dataset checked 24 October 2026. Nothing here is averaged into a new setpoint.",
    "The PLA split is a count of the 60 PLA rows: 14, 9, and 37."
  ],
  "cons": [
    "A 50 °C (122 °F) dryer can meet the 14 PLA rows at or below 50 °C (122 °F). It does not meet the 37 PLA rows whose listed minimum is higher, so it does not cover PLA as a family.",
    "The dataset's community note says 50–70 °C (122–158 °F) dryers are often not hot enough for nylon. That note is not a manufacturer temperature."
  ],
  "community": "",
  "related": [
    "drying",
    "dry_pla",
    "dry_petg",
    "dryer_reco"
  ],
  "faq": [
    {
      "q": "Is a 50 °C (122 °F) filament dryer enough for PETG or nylon?",
      "a": "A 50 °C (122 °F) dryer can dry 19 of 236 filaments in our data, mostly PLA. A filament counts when the maker's drying maximum is at or below that dryer."
    },
    {
      "q": "Does 50 °C (122 °F) cover the PLA rows?",
      "a": "It meets the 14 PLA rows whose listed maximum is 50 °C (122 °F) or less, including Bambu PLA Basic at 50 °C (122 °F) for 8 hours and Prusament PLA at 45 °C (113 °F) for 6 hours on Prusa's drying article. 33 PLA rows list 55 °C (131 °F). Eryone Standard PLA lists 65–75 °C (149–167 °F) for 12 hours. Flashforge PLA-CF lists 60 °C (140 °F) for 6 hours."
    },
    {
      "q": "What is the lowest PETG and nylon temperature in the set?",
      "a": "PETG starts at 55 °C (131 °F). Polymaker PETG TDS V2.0 lists 55 °C (131 °F) for 6 hours, and Prusa's drying article lists Prusament PETG at 55 °C (131 °F) for 6 hours. Nylon starts at 70 °C (158 °F). eSUN ePA lists 70 °C (158 °F) for more than 12 hours, and the Flashforge drying table lists PAHT at 70 °C (158 °F) for 8 hours."
    }
  ],
  "sources": [
    {
      "title": "Bambu Lab PLA Basic technical data sheet",
      "url": "https://cdn.shopify.com/s/files/1/0584/7236/6216/files/Bambu_PLA_Basic_Technical_Data_Sheet_bf3411ce-be39-4db7-9669-1b4671d2196b.pdf?v=1734060943",
      "kind": "datasheet"
    },
    {
      "title": "PolyLite PLA technical data sheet",
      "url": "https://cdn.shopify.com/s/files/1/0548/7299/7945/files/PolyLite_PLA_TDS_EN_V5.4.pdf",
      "kind": "datasheet"
    },
    {
      "title": "Eryone Standard PLA technical data sheet (v1.0, 08/2024)",
      "url": "https://cdn.shopify.com/s/files/1/0252/0412/9841/files/ERYONE-Standard_PLA-TDS.pdf?v=1750747890",
      "kind": "datasheet"
    },
    {
      "title": "PolyLite PETG technical data sheet",
      "url": "https://cdn.shopify.com/s/files/1/0548/7299/7945/files/PolyLite_PETG_TDS_EN_V5.4.pdf",
      "kind": "datasheet"
    },
    {
      "title": "Bambu Lab PETG HF technical data sheet",
      "url": "https://store.bblcdn.com/ce12d65176a94f1086e6aefa238e62e2.pdf",
      "kind": "datasheet"
    },
    {
      "title": "Polymaker HT-PLA technical data sheet",
      "url": "https://cdn.shopify.com/s/files/1/0548/7299/7945/files/Polymaker_HT-PLA_TDS_EN_V1.1.pdf",
      "kind": "datasheet"
    },
    {
      "title": "eSUN product page: ePA-CF",
      "url": "https://www.esun3d.com/epa-cf-product",
      "kind": "manufacturer"
    },
    {
      "title": "Polymaker PETG TDS V2.0 (2025-11-17)",
      "url": "https://polymaker.com/wp-content/uploads/lana-downloads/TDS_Polymaker_PETG_V2.0_2025-11-17.pdf",
      "kind": "datasheet"
    },
    {
      "title": "PolyMide CoPA technical data sheet",
      "url": "https://cdn.shopify.com/s/files/1/0548/7299/7945/files/PolyMide_CoPA_TDS_V5.4.pdf",
      "kind": "datasheet"
    },
    {
      "title": "Prusa Knowledge Base: Drying filament",
      "url": "https://help.prusa3d.com/article/drying-filament_332086",
      "kind": "manufacturer"
    },
    {
      "title": "Drying Temperature and Time | Flashforge Wiki",
      "url": "https://wiki.flashforge.com/en/filaments_and_accessories/Drying_Temperature_and_Time",
      "kind": "manufacturer"
    },
    {
      "title": "eSUN product page: ePA",
      "url": "https://www.esun3d.com/epa-product",
      "kind": "manufacturer"
    },
    {
      "title": "Overture Filament Drying Guide",
      "url": "https://overture3d.com/blogs/overture-blogs/overture-3d-filament-drying-guide",
      "kind": "manufacturer"
    },
    {
      "title": "SUNLU Wiki: filament parameter table",
      "url": "https://www.sunlu.com/wiki/61",
      "kind": "manufacturer"
    }
  ],
  "recommendations": [
    {
      "rank": 1,
      "note": "Bambu PLA Basic technical data sheet lists blast-oven drying at 50 °C (122 °F) for 8 hours. The drying dataset checked that sheet on 18 October 2026. A dryer that holds 50 °C (122 °F) meets this row.",
      "brand": "Bambu Lab",
      "product": "PLA Basic",
      "material": "PLA",
      "url": "/brand/bambu-lab/pla-basic",
      "nozzle": "190–230 °C (374–446 °F)",
      "bed": "35–45 °C (95–113 °F)",
      "pricePerKg": null,
      "datasheetUrl": "https://cdn.shopify.com/s/files/1/0584/7236/6216/files/Bambu_PLA_Basic_Technical_Data_Sheet_bf3411ce-be39-4db7-9669-1b4671d2196b.pdf?v=1734060943",
      "affiliateUrl": null
    },
    {
      "rank": 2,
      "note": "PolyLite PLA technical data sheet lists drying at 55 °C (131 °F) for 6 hours. A 50 °C (122 °F) dryer is below this row. 33 of the 60 PLA rows list 55 °C (131 °F).",
      "brand": "Polymaker",
      "product": "Polylite PLA",
      "material": "PLA",
      "url": "/brand/polymaker/polylite-pla",
      "nozzle": "190–230 °C (374–446 °F)",
      "bed": "25–60 °C (77–140 °F)",
      "pricePerKg": null,
      "datasheetUrl": "https://cdn.shopify.com/s/files/1/0548/7299/7945/files/PolyLite_PLA_TDS_EN_V5.4.pdf",
      "affiliateUrl": null
    },
    {
      "rank": 3,
      "note": "PolyLite PETG technical data sheet lists drying at 65 °C (149 °F) for 6 hours. Every PETG row in the dataset is at least 55 °C (131 °F).",
      "brand": "Polymaker",
      "product": "Polylite PETG",
      "material": "PETG",
      "url": "/brand/polymaker/polylite-petg",
      "nozzle": "220–250 °C (428–482 °F)",
      "bed": "70–90 °C (158–194 °F)",
      "pricePerKg": null,
      "datasheetUrl": "https://cdn.shopify.com/s/files/1/0548/7299/7945/files/PolyLite_PETG_TDS_EN_V5.4.pdf",
      "affiliateUrl": null
    },
    {
      "rank": 4,
      "note": "Overture's drying guide lists Easy Nylon at 95 °C (203 °F) for 7 hours. The catalog stores the same 95 °C (203 °F) for 7 hours. Plain nylon in the dataset starts at 70 °C (158 °F).",
      "brand": "Overture",
      "product": "Easy Nylon",
      "material": "PA6",
      "url": "/brand/overture/easy-nylon",
      "nozzle": "245–260 °C (473–500 °F)",
      "bed": "50 °C (122 °F)",
      "pricePerKg": null,
      "datasheetUrl": null,
      "affiliateUrl": null
    }
  ]
}